Accessories

Tap Adaptor Duotight - 8mm (5/16”) x 5/8” Female BSP Thread. Looking for high quaility push in fittings that will seal tight?  duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design. Why do we use Double O-rings?The secret to our superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them.  The double o-ring means we literally have twice the sealing surface surface when compared with other push in fittings.  This makes our fittings even more reliable and reduces the chance of a leak significantly. The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market. Compatible with: - EVABarrier 6mm ID x 9.5mm OD line- PE-tubing 3/8" (9,5mm) No clamps necessary! We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

Tap Adaptor Duotight - 8mm (5/16”) x 5/8” Female BSP Thread. Looking for high quaility push in fittings that will seal tight?  duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design. Why do we use Double O-rings?The secret to our superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them.  The double o-ring means we literally have twice the sealing surface surface when compared with other push in fittings.  This makes our fittings even more reliable and reduces the chance of a leak significantly. The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market. Compatible with: - EVABarrier 6mm ID x 9.5mm OD line- PE-tubing 3/8" (9,5mm) No clamps necessary! We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

Ball lock connector with Flow Control, to adjust resistance easily without the introduction of turbulence which creates foam. With Duotight 8 mm (5/16"). For liquid/beer.

Self-closing quick disconnect for ball lock cornelius kegs. Black coupling that fits on the liquid post. Barb: 6.5 mm (1/4"). The gas line should be secured with a hose clamp.

Self-closing quick disconnect for ball lock cornelius kegs. Whte/Grey coupling that fits on the gas post. Barb: 6.5 mm (1/4"). The gas line should be secured with a hose clamp.

You can now have a check valve integrated into your ball lock disconnect. These clear/grey high quality plastic disconnects are very common in the industry but now have the added feature of having a check valve integrated into the fitting. The internal parts are made from stainless steel and the body is clear so you can see whats inside.With the MFL thread you can attach: - Barb fitting (Swivel Nut & Barb)- 8mm push in fitting- Mini All In One Regulator- Premium Mini Regulator

Self-closing quick disconnect for ball lock cornelius kegs. Black coupling that fits on the liquid post. Threads: 1/4" MFL (corresponds to 7/16" UNF).

Self-closing quick disconnect for ball lock cornelius kegs. White/grey coupling that fits on the gas post. Threads: 1/4" MFL (corresponds to 7/16" UNF).

Ball coupling with integrated Duotight 6.35mm (1/4") quick coupling. Ingenious ball coupling from kegland means you don't have to choose between hose clamp or quick coupling with threads. Now there is finally a ball coupling in really good plastic material that better resists chemicals and has a built-in quick coupling. For hoses with 1/4" outer diameter.

Ball lock disconnect with integrated Duotight 6,35mm (1/4") quick coupling. Ingenious ball coupling from kegland means you don't have to choose between hose clamp or quick coupling with threads. Now there is finally a ball coupling in really good plastic material that better resists chemicals and has a built-in quick coupling.

Ball coupling with integrated Duotight 8mm (5/16") quick coupling. Ingenious ball coupling from kegland means you don't have to choose between hose clamp or quick coupling with threads. Now there is finally a ball coupling in really good plastic material that better resists chemicals and has a built-in quick coupling. For hoses with 8mm outer diameter.

Ball coupling with integrated Duotight 9,5mm (3/8") quick coupling. Ingenious ball coupling from kegland means you don't have to choose between hose clamp or quick coupling with threads. Now there is finally a ball coupling in really good plastic material that better resists chemicals and has a built-in quick coupling. For hoses with 9,5mm outer diameter.

Ball lock disconnect with integrated Duotight 9,5mm (3/8") quick coupling. Ingenious ball coupling from kegland means you don't have to choose between hose clamp or quick coupling with threads. Now there is finally a ball coupling in really good plastic material that better resists chemicals and has a built-in quick coupling.

The filter prevents hop residue etc from beeing sucked up into a hose, use in kegs, fermenters etc (not with float). Made from HDPE and 304 Grade stainless steel mesh this product can be boiled or sanitized with most detergents.The float can be mounted in three different places on the filter, to determine how close to the surface you want to suck up liquid.Dimensions: 40 x 28 mm. Hose holder diameter: 8 mm, perfect for 6mm inner diameter silicone tube/hose. Materials: Stainless steel 300 mesh and plastic. NOTE: dont use with float as there are no attachments for float on the filter

Brewly Seals 10-pack for Carbonation Caps & Ball Locks

Brewly Stainless Float With Silicone Dip Tube 80cm. Ensure that only the top layer of beer is poured from the fermenter, also fits Fermzilla perfectly. Silikcone tube measurements (dip tube):Inner diameter: 6mm (ID 0.23”)Outer diameter: 8mm (OD 0,35”) Floater diameter: 43mm

Fits CO2/Beer Ball-lock-coupling. Sanitize hoses or force carbonate beer on PET Bottle. Also fits FermZilla. Clean your beer line easy. Attach the cap to a soda bottle with cleaning solution. Liquid and Gas ball lock compatible. Stainless steel.Liquid and Gas ball lock compatible. Barbed fitting fits 4mm, 5mm & 6mm ID flexible hoses.

Add this pressure kit to your FermZilla 27L, 35L or 55L and turn your FermZilla into a true uni tank that can be used for carbonating beer. Stainless steel.Brewly Stainless Pressure Kit includes:- 2 x Carbonation Screw Caps with barb- 1 x SS Float & 80cm Silicone Dip TubeThis inexpensive upgrade will truly show you what the FermZilla was designed for. Here are some possibilities:Fermenting Under Pressure:First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. Carbonating, Pushing, and Serving:When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator. Lack of OxidationBecause the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock. Key Features:• Ferment beer under pressure to reduce ester and fusel alcohol production• Ability to always draw clear beer with the unique, floating draw tube • Keg already carbonated beer• Use co2 to push beer into a keg or though a filter into a keg• Carbonate and serve beer directly from the FermZilla, eliminating kegging all together.

Fits CO2/Beer Ball-lock-coupling and has 1/4" (6,5mm) stem. Sanitize hoses or force carbonate beer on PET Bottle. Also fits FermZilla. Clean your beer line easy. Attach the cap to a soda bottle with cleaning solution. Liquid and Gas ball lock compatible. Red plastic. 1/4" (6,5mm) straight stem fits flexible hoses with inner diameter of 5-6mm, or PE-hoses using a pushfit/duotight connector 1/4".

Fits CO2/Beer Ball-lock-coupling and has 1/4" (6,5mm) straight stem. Sanitize hoses or force carbonate beer on PET Bottle. Also fits FermZilla. Clean your beer line easy. Attach the cap to a soda bottle with cleaning solution. Liquid and Gas ball lock compatible. Yellow plastic. 1/4" (6,5mm) straight stem fits flexible hoses with inner diameter of 5-6mm, or PE-hoses using a pushfit/duotight connector 1/4".

Cooling jacket with extra high performance cooling capacity for Party keg 5 liter. Put in the freezer and when it's time you put the jacket over the keg and thus keep it colder for longer during trips, transport or when the keg is in front of you for serving.

Standard lid for cornelius kegs with Pressure Release Valve (PRV) and o-ring. Oval.

Standard lid for cornelius kegs.

Cornelius Keg Silicone Gasket Set, includes: 1 big o-ring for lid, 2 small o-rings for posts, 2 small orings for the pipe.

Dip Tube for Cornelius keg 18/19L for liquid/beer (bent). Stainless steel.

Dip Tube for Cornelius keg 9L for liquid/beer (bent). Stainless steel.

Dip Tube Gas for Cornelius keg 9/12/18/19L (straight). Stainless steel.

Drip tray for Party Keg 5L, black plastic.

Tap Adaptor Duotight - 8mm (5/16”) x 5/8” Female BSP Thread. Looking for high quaility push in fittings that will seal tight?  duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design. Why do we use Double O-rings?The secret to our superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them.  The double o-ring means we literally have twice the sealing surface surface when compared with other push in fittings.  This makes our fittings even more reliable and reduces the chance of a leak significantly. The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market. Compatible with: - EVABarrier 6mm ID x 9.5mm OD line- PE-tubing 3/8" (9,5mm) No clamps necessary! We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

Tap Adaptor Duotight - 9.5mm (3/8”) Pushfit x 5/8” Female BSP Thread. Looking for high quaility push in fittings that will seal tight?  duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design. Why do we use Double O-rings?The secret to our superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them.  The double o-ring means we literally have twice the sealing surface surface when compared with other push in fittings.  This makes our fittings even more reliable and reduces the chance of a leak significantly. The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market. Compatible with: - EVABarrier 6mm ID x 9.5mm OD line- PE-tubing 3/8" (9,5mm) No clamps necessary! We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

Tap Adaptor Duotight - 9.5mm (3/8”) Pushfit x 1/2” Female BSP Thread. Looking for high quaility push in fittings that will seal tight?  duotight are the push in fitting with superior sealing capacity due to the double o-ring sealing design. Why do we use Double O-rings?The secret to our superior sealing performance is not just the fact that we use high quality EPDM o-rings but also use two of them.  The double o-ring means we literally have twice the sealing surface surface when compared with other push in fittings.  This makes our fittings even more reliable and reduces the chance of a leak significantly. The double o-ring system also means that we can bend the hose with much tighter radius without causing leaking issues.  This typically can be an issue with other fittings.  This combination of factors makes duotight fittings the most reliable push fit fittings on the market. Compatible with: - EVABarrier 6mm ID x 9.5mm OD line- PE-tubing 3/8" (9,5mm) No clamps necessary! We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi.

Add this pressure kit to your FermZilla 27L, 35L or 55L and turn your FermZilla into a true uni tank that can be used for carbonating beer. This inexpensive upgrade will truly show you what the FermZilla was designed for. Here are some possibilities:Fermenting Under Pressure:First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. Carbonating, Pushing, and Serving:When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator. Lack of OxidationBecause the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock. Key Features:• Ferment beer under pressure to reduce ester and fusel alcohol production• Ability to always draw clear beer with the unique, floating draw tube • Keg already carbonated beer• Use co2 to push beer into a keg or though a filter into a keg• Carbonate and serve beer directly from the FermZilla, eliminating kegging all togetherFermZilla Red Plastic Pressure Kit includes:- 2 x Carbonation Screw Caps with barb- 1 x FermZilla 27L, 35L & 55L SS Floater & 60cm Silicone Dip Tube

Fits CO2/Beer Ball-lock-coupling. Sanitize hoses or force carbonate beer on PET Bottle. Also fits FermZilla. Clean your beer line easy. Attach the cap to a soda bottle with cleaning solution. Liquid and Gas ball lock compatible. Stainless steel.

If you want an easy way to balance your beer lines this is the way to do it.  Please be aware that even in the fully open position these FC disconnects do have some inherent flow resistance so you should use either shorter line or larger ID line that you would when compared with traditional ball lock disconnects.  One of the benefits of FC disconnects is you don't need to rely on the small ID or line length to apply flow resistance so it would not make sense to use long lines or small ID lines as well as this is the job of the FC device.This is perfect for people who want to serve a large range of beverages with differing carbonation levels as it gives you the ability to adjust resistance easily.This stainless steel ball lock disconnect is quality machined from stainless steel with MFL thread.  It's ideally used with duotight MFL fittings.

Fluidfit® HCF-UNF push-fit connection connection with female 1/4" thread UNF - connector. For 5/16" hose. N1/4" (UNF7/16-20G) and 5/16" pushfit.

Fluidfit® HCF 1/2" push-fit connection with female 1/2" BSPP thread.

Fluidfit® HCF-UNF 3/8" push-fit connection with female 1/2" BSPP thread.

Fluidfit® HCF-UNF push-fit connection connection with female 1/4" thread UNF - connector adaptor. For 3/8" hose. N1/4" and 3/8" pushfit.

Fluidfit® HCF-UNF push-fit connection connection with female 7/16" thread UNF (1/4" FFL/MFL thread) - connector adaptor for threaded ball disconnects. For 3/8" hose. UNF 7/16" and 3/8" pushfit.

Gas Manifold - CO2 Manifold 5-Way 1/4" MFL - can be used to connect several kegs to a CO2 cylinder. Outlets can be closed and opened individually with built-in check valves. The input and outputs have MFL threads. These are compatible with quick connectors with FFL threads from DuoTight and John Guest, among others.(Hint: MFL stands for Male-, FFL stands for Female-). - Save money by using a single CO2 tank for multiple kegs.- Inlets and outlets are equipped with 1/4" (6.35mm) MFL (fits 7/16" - 20UNF FFL).- Behind the MFLs there is a 1/4'' thread for e.g. ball locks with MFL thread.- Integrated check valve outlets prevent fluid from flowing into the manifold and your regulator, and fluid migrating from one barrel to another.- No leaks due to thread tape and heavy water testing after installation- Body made of aluminium. Rest made of brass and stainless steel.- Mounting holes allow for easy installation on walls or kegerators.

Gas Manifold - CO2 Manifold 6-Way 1/4" Barb - can be used to connect 6 kegs to a CO2 cylinder. Outlets can be closed and opened individually with built-in check valves.  - Save money by using a single CO2 tank for multiple kegs.- Inlets and outlets are equipped with 1/4" (6.35mm) nipple (fits 6mm hose).- Behind the nipples there is a 1/4'' thread for e.g. ball locks with NPT thread.- Integrated check valve outlets prevent fluid from flowing into the manifold and your regulator, and fluid migrating from one barrel to another.- No leaks due to thread tape and heavy water testing after installation- Body made of aluminium. Rest made of brass and stainless steel.- Mounting holes allow for easy installation on walls or kegerators.

Gas Manifold - CO2 Manifold 6-Way 1/4" MFL - can be used to connect several kegs to a CO2 cylinder. Outlets can be closed and opened individually with built-in check valves. The input and outputs have MFL threads. These are compatible with quick connectors with FFL threads from DuoTight and John Guest, among others.(Hint: MFL stands for Male-, FFL stands for Female-). - Save money by using a single CO2 tank for multiple kegs.- Inlets and outlets are equipped with 1/4" (6.35mm) MFL (fits 7/16" - 20UNF FFL).- Behind the MFLs there is a 1/4'' thread for e.g. ball locks with MFL thread.- Integrated check valve outlets prevent fluid from flowing into the manifold and your regulator, and fluid migrating from one barrel to another.- No leaks due to thread tape and heavy water testing after installation- Body made of aluminium. Rest made of brass and stainless steel.- Mounting holes allow for easy installation on walls or kegerators.

Gas distributor 3 outputs 1/4 nipple. Perfect when you build a kegerator and want to be able to have several barrels on the same carbon dioxide tube and then also have the option to turn off or on the gas to each barrel.

Gas distributor 4 outputs 1/4 nipple. Perfect when you build a kegerator and want to be able to have several barrels on the same carbon dioxide tube and then also have the option to turn off or on the gas to each barrel.

Hop filter in stainless steel, perfect for dry hopping beer in Cornelius kegs or fermenters. Loop for hanging it. Length: 18cm. Diameter: 7cm. Mesh size: 300 microns

Hop filter in stainless steel, perfect for dry hopping beer in Cornelius kegs or fermenters. Loop for hanging it. Length: 29cm. Diameter: 7cm. Mesh size: 300 microns

Isolation Jacket for Cornelius Keg 18-23L. Neoprene.Note: Cornelius keg is not included.

The filter prevents hop residue etc from beeing sucked up into the silicone hose of the FermZilla Float. Made from HDPE and 304 Grade stainless steel this product can be boiled or sanitized with most detergents.The float can be mounted in three different places on the filter, to determine how close to the surface you want to suck up liquid.Dimensions: 40.5 x 27 mm. Hose holder diameter: 7.20 mm, perfect for 6mm inner diameter silicone tube/hose. Materials: Stainless steel and plastic. design may vary.

The Duotight Flow Stopper - Automatic Keg Filler (KL09393) is an fantastic device designed to streamline the keg filling process for homebrewers. This product,  offers a hassle-free method of filling kegs, or transferring between kegs during filtering or after fining. It is particularly useful because it attaches to the gas post of your keg and automatically cuts off the flow once the keg is full, thus preventing overfilling and spillage of beer. Some of its key features include compatibility with Duotight fittings, ensuring a secure and leak-free connection, and the ability to work with a BlowTie spunding valve. When used with the BlowTie, it allows you to apply head pressure to the keg, enabling control over the flow speed and reducing foam during the filling process.For this setup, a short length of 8 mm OD EVABarrier tubing is required to connect the BlowTie to the outlet of the Flow Stopper. This flow stopper includes:2 x duotight 5/8" thread x 8mm pushfit (for hose)1 x duotight Elbow pushfit 8mm1 x duotight straight 8mm pushfit x 7/16" thread for threaded ball lock1 x ball float1 x stainless spring1 x acrylic sight glass (with 5/8 male thread on either side)*Colours of the floating ball and joiners may vary. You need to buy a ball lock with a thred if you do not have one. 

Kegland Oxygen Flow Meter with 8mm Duotight. Pure oxygen is the best way to get your yeast off to a cracking start. Simply use this high pressure and high capacity disposable tank to boost dissolved oxygen levels in your cooled wort.Oxygen is great for use with high gravity beers or pilsners where you are trying to build up a large population of yeast.We would recommend the use of a diffusion stone. These small diffusion stones create very fine bubbles of oxygen in your wort and help the oxygen to dissolve into solution faster. If you want a really nice optoin we would recommend the use of this oxygenation wand and this is a bit more erganomic as you have a rigid stainless tube to force the stone to the bottom of the fermenter rater than it floating to the surface.This flow control device is designed to be used with our oxygen cylinder and regulator that can be purchased separately.InstructionsAttach the regulator to to the top of your disposable cylinder. Turn pressure up to 1-10psi. Immerse diffusion stone in wort for 1-2 minutes. Then dial the flow meter up to 1.0L/min. The time it takes to saturate will depend on volume, temperature, depth of vessel, and type of stone (0.5mm recommended)NOTE: Wort must be cold. It is extremely difficult to get oxygen to dissolve into hot wort so it's essential to cool wort completely before starting this process.