Brewtools

Brewtools B40pro Brewing System (EU)
The Brewtools B40pro is a brewing system without compromise. Built for enthusiasts.- 46-liter (12 gal) tank volume and 9kg (20 lb) malt capacity.- 20-40 liter (5-11 gal) pre-boil volume for flexibility- 3,2kW heating power makes heating and boiling fast.- High accuracy with 2 digital sensors.- Conical bottom with center draining for fast and easy cleaning.- Powerful control system with 7" touch-screen, Wifi and Bluetooth 4.2.The B40pro has an 40 liter (10 gal) boil capacity and about 9kg (20 lb) malt capacity. It is equipped with a powerful pump, which can be controlled from the touch-screen. The wort is circulated up through the center-pipe and the pump is fitted using Tri-Clamps making it very easy to remove, even when the tank is full.The malt pipe has latches that folds out when you lift it, so you can use both your hands for lifting.Sparging is done without tubes or pipes outside the tank. A sparge tube installed on the outside of the centerpipe follows the malt pipe when lifted also lifting the wort spreading device. This makes it very easy to sparge from a separate tank without making a mess.After brewing with the B40pro, you never have to turn it upside down for cleaning. The centerpipe is removed easily, and you can easily clean the unit, and all the trub will be drained directly to a bucket or the drains. Use the included circulation device as a CIP solution to save time and cleaning chemicals.The system has two digital temperature sensors - one in the bottom of the tank and one before the pump. The maxium static offset is ±0,5°C. The sensors can be individually calibrated for maximum accuracy. They have an accuracy of 0.1°C. It's also possible to connect a third sensor (accessory) to monitor the temperature of the wort returning from the counterflow cooler, so you can pump directly to the fermenter when the temperature is right.With powerful heating elements combining over 3,2kW (230V) of power, heating the water or wort is very fast. During the boil, the PID system is deactivated and you can adjust the power output to achieve the perfect rolling boil. You can also adjust the maximum current of each mains input, to 10, 13, 15 and 16 Amps, to make sure you never blow a fuse.All ports are 34mm Tri-Clamp fittings for maximum flexibility without leaks. As standard the system is shipped with one 3-way valve. All silicone tubes are 16x25mm food grade silicone.The control system is custom developed and features high quality electronics. The software is constantly being improved with new features. It is updated via WiFi. What's included:– Complete brewing system with controller, pump, tank sensor, heaters and lid– Malt pipe with handle and latches– 1 pcs expanded metal filter– 1 pcs 3-way valve– Temperature sensor with adapter for pump line– 5 pcs 34mm Tri Clamps with gaskets (all used for standard setup)– 3 pcs 34mm TC blind caps– 1 pcs dip tube, short type– 1 pcs mash hat for spreading the wort– 1 pcs sparge tube– 150cm 16x25mm silicone tube– 1 pcs 34mm TC to 19mm hose barb adapter– O-rings for the center pipe and dip tube– 1 pcs Power Cable, 2 meterPlease note that some parts of our systems are made by hand, and might have some minor cosmetic imperfections. This will not affect the functionality of the product.SpecificationDimensions excl. packaging:58 (h) x 52 (w) x 52 (d) cmDimensions with one side valve:58 (h) x 62 (w) x 52 (d) cmDimensions with two valves:58 (h) x 72 (w) x 52 (d) cmPackaging dimensions:70 (h) x 55 (w) x 55 (d) cmWeight excl. packaging:20 kgWeight incl. packaging:24.5 kgTank dimensions:Ø40 cm, height 36 cmTank volume:46 liters (rec maximum boil volume – 40 liter)Malt pipe dimensions:Ø32 cm, height 32 cmMalt pipe volume:25.7 lMax recommended grain quantity:9 kgMinimum liquid volume:15 lBuild material:1.0 mm stainless steel (SS304)Heating elements:230V, 3200W (2x1600W)Pump:24VDC brushless, max 25 l/min, max head 4.5 m, stainless steel head, stepless speed control from touch displayController:ARM Cortex M4 180mhz, 7" Touch displayConnectivity:WiFi 802.11 b/g/n, Bluetooth 4.2, MicroSDHoses:16x25mm silicone, food grade Brewtools Documentation Link

Brewtools Starter Pack 3-valve Setup
This is the recommended accessories to get you started using Brewtools pro systems, B40pro/B80pro/B150pro. The package includes an efficient counterflow cooler, an extra 3-way valve to make you able to choose if you return the cooled wort to the tank creating a whirlpool or pump directly to the fermenter. The third 3-way valve makes it possible to clean the system without disconnecting hoses.The adjustable dip tube is included in this package for optimal control during pumping to fermenter.A third sensor gives you exact measurements of the wort returning from cooling. The necessary fittings and accessories are also included.Fittings for connecting a sparge water heater is not included.Included in the package:- 2 pcs 3-way ball valve, TC34mm DN15- 1 pcs Dip tube, Adjustable, TC34mm- 1 pcs Counterflow Cooler, Pro- 3 meter Silicone Tube 16x25mm, clear- 3 pcs TC Gasket, 34mm, DN15, 5-pack- 2 pcs TC34mm to 12mm hose barb- 1 pcs TC34mm to 19mm hose barb, sensor holder- 5 pcs TC34mm to 19mm hose barb- 1 pcs Temp. Sensor, inline, M10- 8 pcs Tri Clamp, 34mm- 1 pcs TSP, 100g

Brewtools B40pro Insulation Jacket
Flexible insulation jacket for your Brewtools B40pro. Zippers make it easy to take on and off the brewer. It insulates and retains heat better so you use less energy to heat the vessel.· Black· 5 mm thick neoprene· White logo

Brewtools B150pro Insulation Jacket
Flexible insulation jacket for your Brewtools B150pro. Zippers make it easy to take on and off the brewer. It insulates and retains heat better so you use less energy to heat the vessel.· Black· 5 mm thick neoprene· White logo

Brewtools Trubinator S
Brewtools Trubinator S can be used in Brewtools B40 brewing system. During the whirlpool, hops and other particles will collect in the middle of the filter, making it possible to pump out clearer wort to your fermenter.A single wingnut and bolt holds the filter in place, so it's easy to disassemble for cleaning.Diameter: 320mmHeight: 90mmStandard filter: R2x5

Brewtools Sparge Manifold S
Sparge manifold for simple spreading of sparge water over the grains. It can also be used as a mash manifold during mashing for a more efficient distribution of wort over the grainbed. Made for Brewtools B40Pro and is attached to the center pipe and follows when the malt pipe is liftet up for sparging. Top and end-plugs made in the Brewtools characteristic blue silicone for easy access for cleaning after use. Diameter: 260mmIncludes:- Manifold- Top plug in silicone- End plugs in silicone

Brewtools Sparge Manifold M
Sparge manifold for simple spreading of sparge water over the grains. It can also be used as a mash manifold during mashing for a more efficient distribution of wort over the grainbed. Made for Brewtools B80Pro and is attached to the center pipe and follows when the malt pipe is liftet up for sparging. Top and end-plugs made in the Brewtools characteristic blue silicone for easy access for cleaning after use. Diameter: 360mmIncludes:- Manifold- Top plug in silicone- End plugs in silicone

Brewtools Sparge Manifold L
Sparge manifold for simple spreading of sparge water over the grains. It can also be used as a mash manifold during mashing for a more efficient distribution of wort over the grainbed. Made for Brewtools B150Pro and is attached to the center pipe and follows when the malt pipe is liftet up for sparging. Top and end-plugs made in the Brewtools characteristic blue silicone for easy access for cleaning after use. Diameter: 420mmIncludes:- Manifold- Top plug in silicone- End plugs in silicone

Brewtools Counterflow chiller 5m
Counterflow chiller specially designed for all Brewtool models. With this countercurrent cooler, you can ensure that you get a quick and efficient cooling of the wort without giving in to the Whirlpool effect. Five meter wound stainless steel pipes with welded 34 mm Tri-Clamp couplings. Produced from 304 stainless steel. 4 34 mm Tri-Clamp couplings, two for wort and two for water.

Brewtools Bracket for Control Box B40/B80/B150
Bracket for mounting the control box for your brewing system on the wall/table or on a VESA-mount arm. Used in combination with the cable extension kit. Features VESA75 and VESA100 with M4 threads. Made in powder coated stainless steel. Fits Brewtools B40/B80/B150.

Brewtools Cover Plate B40/B80/B150
Cover plate to cover the controller hole when relocated. Black, powder coated stainless steel. 4x bolts and nuts included. Fits Brewtools B40/B80/B150.

Brewtools Inline Oxygenation Kit
An inline oxygenation kit for B40, B80 & B150 designed to inject oxygen during transfer to fermenter. We recommend placing a sight glass after the TC tee, to keep an eye on the O2 flow. Requires an oxygen tank with a pressure regulator.Included:- TC34mm Tee- Barbed O2/Co2 stone holder, 6-10mm tube- O2/Co2 stone, 0.5micron. G1/8" threads- 3 TC34mm clamps- 1 5-pack of TC34mm gaskets- 1 gasket for the stone

Brewtools Inline Filter Kit 2" Ball Lock
Brewtools filters are installed directly on the butterfly valve on the yeast tank. The filter can be used for other purposes as well and can be adapted with most accessories and adapters. If the filter clogs, you just need to remove a Tri Clamp and rinse it off with disinfectant without having to disassemble all parts. USE: Install the filter after disinfection. Install the filter kit on the butterfly valve Blow through with Co2 a couple of times Open the valve and release the air with PRV Connect the ball coupling to your drum If the filter is to be used with liquid above 60 degrees, we recommend that you replace the Poly TC tube and the filter holder with the stainless steel options Filter holder | Stainless | Brewtools and Pipes | 20 cm | 2 "TC | Brewtools or use our stainless steel filter In-line Sanitary Filter | 1.5" TC. You can easily put several filters one after the other if you want a coarse filter first and a finer one afterwards. < br /> INCLUDED PARTS: Ball lock adapter, 2 "with M16 threads 3 pcs Filters in stainless steel 30mm, 300, 600 and 1000 microns Filter holder made of food grade Nylon (PA), M16 TC 2 "to 34 mm T-cross TC34 mm manual PRV 3 pcs 2" Tri Clamp 1 pc 34 mm Tri Clamp 2 pcs TC gasket with filter groove (blue) 1 pc 2 "Poly TC pipe, 200 mm 2" and 34 mm gaskets

Brewtools Overflow pipe kit
The overflow pipe kit is a solution for the malt pipe in our brewing system. It makes it simple to avoid dry heating elements and grains in your wort.The system is fastened to your filter (Punch out the pre-cut hole in the laser cut filter or use a 25mm hole punch for the standard filters).It's adjustable from about half batch to a full malt pipe.Note: We never recommend to run a high power brewing system without supervision. This safety solution does not guarantee avoiding burnt heating elements due to dry running.Included in the package:- Overflow pipe with M24 threads, 180mm- Pipe kit, 200, 300 and 400mm)- Silicone parts- Filter, laser cut- M24 nut- M24 hole cover

Brewtools TC 34mm Thermowell short
Thermowell for sensors. TC 34mm. Inside diameter: 7mm Length: 90mm

Brewtools TC 34mm Thermowell long
Thermowell for temperature sensors. TC 34mm.Inside diameter: 7mmLength: 160mm

Brewtools TC 1,5" Thermowell short
Thermowell / diving well for sensors. Triclamp coupling 1.5 ". Inside diameter: 7mm Length: 90mm

Brewtools TC 1,5" Thermowell long
Thermowell for sensors. Triclamp coupling 1.5 ". Inside diameter: 7mm Length: 160mm.

Brewtools Provtagningskran TC34mm
Sampling crane to take samples from the tank during the fermentation process. Can also be used at start-up together with B40 / 80/150 Pro to take samples of the wort during the brewing day. Triclamp 34mm.

Brewtools HopDrop Kit 3"
Brewtools HopDrop Kit 3" for dryhopping and adding other ingredients to a pressurized fermenter without oxygen. Fits F40/F80 and other 3".Included in the box:- Butterfly-valve, TC 3"- TC Adapter, 3" to 34mm- TC Pipe, 3", L=200mm - Tri Clamp, 3" (2 pcs)- Tri Clamp, 34mm (3 pcs)- TC34mm Manual PRV- TC34mm Ball Lock connector, Gas- TC Tee, 34mm, L=60mm- TC Gasket, 3", (3 pcs)- TC Gasket, 34mm DN20, 5-pack

Brewtools HopDrop Kit 4"
Brewtools HopDrop Kit 4" for dryhopping and adding other ingredients to a pressurized fermenter without oxygen. Fits F100/F150/F200/F300 and other 4".Included in the box:- Butterfly-valve, TC 4"- TC Adapter, 4" til 34mm- TC Pipe, 4", L=200mm - Tri Clamp, 4" (2 pcs)- Tri Clamp, 34mm (3 pcs)- TC34mm Manual PRV- TC34mm Ball Lock connector, Gas- TC Tee, 34mm, L=60mm- TC Gasket, 4", (3 pcs)- TC Gasket, 34mm DN20, 5-pack

Brewtools F40 Unitank 40L Fermenter
Our Unitanks are fermenters made for ambitious homebrewers and small breweries. As part of the Brewtools identity, we've explored new techniques and solutions. This has resulted in a series of high end fermentation tanks with new features and a lot of possibilities.Key Features:- Our PureBlast™ surface inside and out which eliminate the use of wax and polishing compounds and does not require passivation.- Cooling jacket in the vertical walls offers efficient cooling without the hazzle of cleaning a spiral.- Many options for connecting accessories like sensors, heaters, carb. stones and other accessories.- Pressure rated for 2 bar / 30 PSI.- 8" TC port on top for easy access.- 2" TC dump and racking valves.Our Unitanks are designed and manufactured with special attention to safety and quality. They are tested and certified according to the requirements for PED 2014/68/EU by a third party.Specifications:- Low height w/o acc.: 83 cm- Max height w/o acc.: 103 cm- Packaging size: 85 (h) x 52 (w) x 52 (d) cm - Net weight: 38 Kg- Gross weight: 44.6 Kg- Tank diameter (inside): Ø40 cm- Gross volume: 51 liter- Max rec. volume: 40 liter- Min rec. volume: 20 liter- Volume, cone: 12 liter- Material: 1.5mm stainless steel (SS304)- Operating pressure: 1.0 bar / 15 PSI- Max pressure: 2.0 bar / 30 PSIIn the box:- Unitank with adjustable frame- 1 pcs Analog pressure gauge, TC34mm- 2 pcs Butterfly-valve, 2"- 1 pcs Butterfly-valve, 34mm DN20- 1 pcs Blow-off pipe- 1 pcs Racking arm 2"- 1 pcs TC elbow 90°, 2"- 1 pcs Insulation jacket, black neoprene- 1 pcs Sample valve, 34mm- 1 pcs TC Adapter 8"-3"- 1 pcs TC blind cap, 3"- 1 pcs TC blind cap 2"- 2 pcs TC blind cap 1.5"- 3 pcs TC blind cap 34mm- 2 pcs TC gasket 8" lipped- 2 pcs TC gasket 3"- 2 pcs TC gasket 2" 5-pack- 1 pcs TC gasket 1.5" 5-pack- 3 pcs TC gasket 34mm 5-pack (DN20)- 1 pcs Tri Clamp 8"- 1 pcs Tri Clamp 3"- 5 pcs Tri Clamp 2"- 2 pcs Tri Clamp 1.5"- 10 pcs Tri Clamp 34mm- 1 pcs TC tool- 4 pcs M10 steel/rubber feet- 1 pcs TC34mm safety valve (PRV, 2 bar)- Necessary bolts and parts for assemblyRecommended accessories include: HopDrop-kit, Thermowells for your sensors, 34mm Ball-Lock gas adapter for CO2 filling, Carb. stone kit with Ball-Lock, Coil for sample valve, Spunding valve, Hose barbs for filling and dumping, 2" sight glass etc.For more detailed information and user manual, please visit docs.brewtools.com

Brewtools MiniUni 10L
Brewtools MiniUni 10LThe MiniUni™ tanks are a range of high quality flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as heating water, storing cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EU Specification:Pack size: 34 (w) x 34(d) x 61 (h) cmWeight without emaballage: 8 KgWeight with packaging: 9.3 KgTank diameter (inside): Ø28 cmMax. recommended volume: 10 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSIThis comes with: MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-part with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

Brewtools MiniUni 20L
Brewtools MiniUni 20L The MiniUni™ tanks are a series of high quality flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as water heating, storage of cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EU Specification:Pack size: 34 (w) x 34(d) x 61 (h) cmWeight without emaballage: 8 KgWeight with packaging: 9.3 KgTank diameter (inside): Ø28 cmMax. recommended volume: 20 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSI< strong>This comes with: MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-piece with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

Brewtools MiniUni 30L
Brewtools MiniUni 30LThe MiniUni™ tanks are a range of high quality flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as water heating, storage of cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EUSpecification:Pack size: 34 (w) x 34(d) x 77 (h) cmWeight without emaballage: 9.65 kgWeight with packaging: 11.2 kgTank diameter (inside): Ø28 cmMax. recommended volume: 30 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSIThis comes with: MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-piece with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

Brewtools MiniUni 40L
Brewtools MiniUni 40L The MiniUni™ tanks are a range of high quality, flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as water heating, storage of cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EUSpecification:Pack size: 34 (w) x 34(d) x 92 (h) cmWeight without packaging: 11.2 kgWeight with packaging: 12 kgTank diameter (inside): Ø28 cmMax. recommended volume: 40 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSI< strong>This comes with:MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-piece with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

Brewtools MiniUni 50L
Brewtools MiniUni 50L The MiniUni™ tanks are a range of high quality, flexible yeast tanks at a very reasonable price. They can be used for fermentation, storage and serving of beer but also other uses such as water heating, storage of cleaning agents, HERMS installation, etc. MiniUni™ can be placed in the included base but also hung on the wall with the included wall bracket. By using a pressure fermentation kit (optional equipment) you can ferment under pressure and carbonation in the tank.All MiniUni™ are approved for 2 bar (30 psi) and will last a lifetime!! Key Features:PureBlast™ surface inside and out which eliminates the use of wax and polishing agents in manufacturing. The tank also does not need to be passivated.Easy cleaning with 4" Tri-Clamp opening in the top and a 2" Tri-Clamp in the bottomPressure approved up to 2 bar (30 psi)Wall bracket is included Designed and produced with quality in focus. Tested by independent party to meet PED 2014/68/EU Specification:Pack size: 34 (w) x 34(d) x 108.5 ( h) cmWeight without packaging: 12.85 KgWeight with packaging: 14.8 KgTank diameter (inside): Ø28 cmMax. recommended volume: 10 litersVolume, cone: 1.7 litersMaterial: 1.5mm stainless steel (SS304)Maximum pressure: 2.0 bar / 30 PSIThis comes with: MiniUni™ TankBase with silicone gasketWall mount and baseSafety lock for wall mountComposite TC adapter 4" to 34mmIce lock, 3-piece with holderTri-Clamp 4"Tri-Clamp 2"Tri-Clamp gaskets

Brewtools MiniUni Wall Bracket Triple
Stainless steel wall bracket for 3x MiniUni in all sizes. 5 double holes with 150mm spacing makes it easy to install in wall beams.

Brewtools Uppsamlingsbricka
Used, among other things, to avoid spillage when disconnecting TC terminals. Can also be used to collect small parts and gaskets during brewing.

Brewtools Ventilspiral
Spiral that can be mounted on the outside of the sampling faucet from Brewtools. Reduces foam to a minimum when samples are taken from a fermentation tank under pressure.

Brewtools Silicone gasket for 34mm Tri-Clamp
Food-approved gasket for 34 mm Tri-Clamp. Produced in high quality silicone. Fits Brewtools B40Pro & B80Pro.

Brewtools Sight glass Modern Tri-Clamp 2" short
Sight glass with 2 "(64MM) Triclamp couplings. Sight glass with 2" (64MM) Triclamp couplings. Length: 98mm Inside diameter: 47.8mm

Brewtools Sight glass Tri-Clamp 34mm
Sight glass with 34 mm TC connection. The sight glass allows you to see the color of the wort during circulation. Also suitable for oxygenation to see the flow of oxygen. Usually mounted between a 3-way valve and the countercurrent cooler.

Brewtools Power cable H07RN 10 metres
Brewtools power cable 10m. The power cable fits B40pro, B80pro and B150pro. Cable: Rubber, H07RN standard (3x2.5mm2). Contact: CEE 7/7 (16A).

Brewtools Mash paddle (Long)
Paddle made from high quality SS304 steel. The paddle has a practical holder on the shaft to hang it on the inside of the tank or malt pipe and it has a T-handle for comfortable use.Length: 78cm

Brewtools Ball valve straight TC34mm DN15
Brewtools Straight ball valve, TC 34mm. The handle rotates freely for maximum flexibility

Brewtools Butterfly valve TC 2"
Brewtools butterfly valves are developed for use with Brewtools Unitanks for the best possible sanitary properties and ease of cleaning. Made with the highest possible quality of steel and EPDM.

Brewtools Butterfly valve TC 3"
Brewtools butterfly valves are developed for use with Brewtools Unitanks for the best possible sanitary properties and ease of cleaning. Made with the highest possible quality of steel and EPDM.

Brewtools Aeration Spiral
Oxygen air spiral with 1/2 "NPT threads. Used to aerate the wort when you drop it into a yeast tank / fermentation bucket. Made of 316 stainless steel.

Brewtools Weldless Fitting 34mm
Brewtool's weldless flanges are used to expand your system without limitations. Designed and manufactured to minimize visible threads for easier cleaning. (NOTE gasket sold separately)We recommend hole puncher to make perfect holes for the weld-free flanges.

Brewtools Packning till svetsfri flens TC 34mm 2-pack (32x24x2.5mm)
2 pcs silicone gaskets for Weldless Fitting | TC 34 mm | Brewtools