Brewery Accessories

Better Brew Beer Paddle 24" 61cm - Designed for especially for Homebrew. Food grade plastic stirring spoon/paddle. This long handle food grade paddle reaches right to the bottom of pretty much all fermentation vessels, barrels, kegs and buckets. An essential peice of kit.

Better Brew 24" 61cm Long Plastic Spoon - Designed for especially for Homebrew. Food grade plastic stirring spoon/paddle. This long handle food grade spoon/paddle reaches right to the bottom of pretty much all fermentation vessels, barrels, kegs and buckets. An essential peice of kit. (It doesn't fit through the neck of carboys and demijohns of course.)

Insulation jacket for the Brewly 30L Conical Fermenter (both versions). Material: 5 mm neoprene foam.

Heat insulation for the Brewly 40L brewery. Provides faster heating, more vigorous boil and reduces energy consumption. Material: 5 mm neoprene foam.

Brewly 40L Perforated Malt Basket. New open, perforated design for high wort flow. 304 Stainless steel. Höjd: ca 33,5 cmdiameter uppe: ca 37 cmdiameter nere: ca 35 cm

Heat insulation for the Brewly 70L V2 brewery. Provides faster heating, more vigorous boil and reduces energy consumption. Material: 5 mm neoprene foam.

Brewly 70L V2 Perforated Malt Basket. New open, perforated design for high wort flow. 304 Stainless steel. NOTE! Fits only Brewly V2 brewery, not V1 or forst generation 65L & 70L. height: ca 33,5 cmdiameter up: ca 37 cmdiameter down: ca 35 cm

Heat insulation for the Brewly BWH30L brewery & water heater. Provides faster heating, more vigorous boil and reduces energy consumption. Material: 5 mm neoprene foam.

Brewly Flexible Recirculating Arm 40-70L. Spare Part.

Glass cap that fits both 40L and 70L Brewly breweries.

Brewly Bottom Grain Basket Plate for 40L & 70L Brewery. Spare part. Also fits Brewolutions Brewster.

Brewly Top Grain Basket Plate for 40L & 70L Brewery. Spare part. Also fits Brewolutions Brewster.

Spare part. Brewly L-pipe for Brewly Brewery 40L and 70L Pump Inlet. Material is stainless steel. Keeps hop and malt debris at the bottom of the brewery from entering the pump inlet. May also fit Brewolution BB40 and BB70 which has similar construction.The pipe inlet is ca 40mm above the brewery's bottom. Total height avobe bottom is ca 45mm. The pipe length horizontally is ca 110mm.

Spare part. Brewly Malt Basket Ring for 40L/70L Brewery

spare part. Stopper for the telescopic malt basket pipe so malt or grains cannot enter it during mashing in.

Fine-mesh bottom filter to avoid larger particles in the wort during mashing. Also fits Brewolutions Brewster.diameter 355mm

Magnetic Pump MP-10RN, spare part for Brewly Breweries, also fits other breweries. Up to 12L/min. Very quiet, high quality, powerful magnetic pump that can handle wort/water up to 100°C, however its not recommended under sustained periods. Perfect for recirkulating wort and transfer of wort/drikning water. Standard 14mm inlet/outlet.Do not run the pump dry.Specifications Brewly Magnetic Pump MP-10RNCapacity: max 12 L/min (60Hz)Head: max 2,1 meters (60Hz)Power rating: 6WVoltage: 220-240V (50-60Hz)Protection: IP44Tube Interface Inlet: 14 mmTube Interface Outlet: 14 mmNote: Do not run the pump dry

Brewly MP-15RN Magnetic pump 10W, IP44. 5/8" (16mm) input and 5/8" (16mm) output (points upward), not threaded.

Brewly O-ring Kit for 40L/70L brewery. Spare parts.

Brewly Large Pump Hose Adaptor for 40L & 70L Brewery. Silicone. Spare part.

Brewly Small Pump Hose Adaptor for 40L & 70L Brewery. Silicone. Spare part.

Brewly Racking Arm for Conical Fermenter with 2pcs silicone o-rings with 9mm outer diameter and 6mm inner diameter, thickness ca 1,5mm.

The Brewly Hop Spider keeps hops together during the boil, separated from the wort. It can be used on most breweries and kettles. This spider can be used for any kind of hops, including hop pellets.Brewly SS500 Hop SpiderDiameter: 15 cm Height: 35,5 cm Material: 500 micron 304 grade stainless steel mesh, with stainless steel support band and single hook

The Brewly Hop Spider keeps hops together during the boil, separated from the wort. It can be used on most breweries and kettles. This spider can be used for any kind of hops, including hop pellets.Brewly SS800 Hop SpiderDiameter: 15 cm Height: 35,5 cm Material: 800 micron 304 grade stainless steel mesh, with stainless steel support band and single hook

Heavy duty stainless steel mash paddle from Brewly. Length 60cm.

Tap made in 304 stainless steel that fits most breweries. Rubber covered handle with auto-lock function. 1/2" thread with stainless 1/2" nut and silicone seal. 13mm (1/2") barb at the opening (fits 1/2" hose).

Spare part. Brewly Telescopic Malt Basket Tube 40L.

Spare part. Brewly Telescopic Malt Basket Tube 40L.

Graduated volume tube in polycarbonate that fits the Brewly 40L brewer.

Stainless Whirlpool Arm with CAM-lock connector, makes it possible to create a whirlpool in the wort after the boil which increases volume efficiency and speeds up the cooling of the wort. Black neoprene handle.Brewly Whirlpool Arm CAM-lockLength: 40cm, usefull length 35cm.Material: Stainless Steel 304.

Stainless steel bottom filter for Brewster Beacon 40 and 70-liter. Brewolution has developed a completely new "false bottom" that connects directly to the inlet to the pump instead of lying loose over the entire bottom. Instructions can be found here!

Whirlpool arm for Brewster 40L that fits onto the existing recirculation pipe. It recirculates the wort and thereby making a whirlpool at the bottom of the kettle.Length 35,5 cm.

Whirlpool arm for Brewster 70L that fits onto the existing recirculation pipe. It recirculates the wort and thereby making a whirlpool at the bottom of the kettle.Length 39,5 cm.

Brewolution Pump hose Beacon 40L. Silicone. Spare part.

Brewolution Seal for Sight Glass Plug for Brewster Beacon. Spare part.Seal for Level Gauge Plug for Brewster Beacon.

Brewolution Sight Glass Plug for Brewster Beacon. Spare part.Level Gauge Plug for Brewster Beacon. Placed at the top of the Level Gauge.

Brewster Hop Spider with fine stainless steel mesh to keep hops separated from the wort during the boil.InfoMaterial: 304 stainless steelMesh size: 310 micronsTotal height: 38 cmCylinder height: 36 cmDiameter opening: 15 cmDiameter bottom: 10 cm

Neoprene Jackets with recirculation arm cover for stable temperatures and heat retention. 8 mm thick neoprene. Must-buy if you brew where it is cold/windy.

Complete silicone tube kit for connecting the tubes and pump at the bottom. SPARE PARTS

Neoprene Jackets with recirculation arm cover for stable temperatures and heat retention. 8 mm thick neoprene. Must-buy if you brew where it is cold/windy.

Spare part: Roller (crush roller) to Bulldog Malt Mill. 1pcs (2pcs are needed)

Bulldog Mash Paddle in 304 Stainless Steel. 61cm in length.

Coobra Mash Paddle in 304 Stainless Steel. 60cm in length.

Spare part pump MP-10RN for Coobra CB3 & CB5. Standard 14mm input/output. Standard pump for many breweries. Colours may vary.

Digital spoon scale with 3 different size spoons. Perfect when measuring water treatments or hops. High 0,1 gram precision.- Weighs up to 500 grams with 0,1g precision.- Choose between 4 units: gram, oz, gn eller ct.- Easy to clean: just remove  the spoon and wash.- Easy-to-read LCD-display.- Energy saving auto-off function.- Tare and Hold function.- Batteries not included (2pcs 5V AAA).- Manual in English.

Upgrade your G30 Brewing System with the G30 Hop Plate, a purpose-built false bottom style hop plate filter for use with all G30 Brewing Systems. Install alongside the system's current filter for increased efficiency in hop filtration.How to Use:- Install the G30 Filter (this is the hop filter included with the G30) as per the instructions included with the G30 Brewing System.- Install the G30 Hop Plate by placing the plate feet down into the boiler over the top of the G30 Filter, so the feet of the hop plate rest flat on the base of the boiler. Features:- Sleek, high-quality 304 grade stainless steel construction- Easy to clean- Full body false bottom style filter for even better hop filtration- Designed specifically for use with the G30 Brewing SystemSpecifications- Stainless steel construction: (0.9 mm Thickness)- Outer diameter (Width): 29.5 cm Height: 5.1 cm- Perforation diameter: 1.8 mmNote: Some users may experience a slight reduction in boil vigour and slight increases in heating time.Caution: Post-boil hop matter will retain heat. Always use thermally insulated gloves when removing the hop plate post boil.

This High Performance Cleaner is specially formulated to be used with the Grainfather. It removes hard to clean proteins from your Grainfather without the need for tedious scrubbing. Perfect for cleaning hard to reach places such as the counter flow wort chiller, pipes and pumps.This is suitable for soft (copper) and hard (stainless steel) metals which not many other cleaners do. It is important you use this to clean your Grainfather as other cleaners may, over time, damage your system.Use- Add 2 Tbsp of cleaner to 15 L of water at 60°C to your Grainfather. - Attach the counter flow wort chiller and recirculate the cleaner for 15 minutes. - Remove the counter flow wort chiller and attach the recirculation pipe and recirculate for another 5 minutes. - Rinse all surfaces that came in contact with the cleaner thoroughly with winter. - Gently scrub the inside of the boiler with a soft bristle brush to remove left over stains. Rinse and drain.

This Hop Spider keeps hops together during the boil. It can be used on all appropriate sized boil pots, including the Grainfather. Made with a coarser, 800 micron mesh, for maximum wort flow and increased hop utilisation. This spider can be used for any kind of hops, including hop pellets.Although it is not a necessity in brewing with the Grainfather brewing system, it is a popular product. This has therefore been designed with a specifically fitted hook design which can be hooked onto the side of any brew pot or the Grainfather support ring. Perfect for those of you who would like the reassurance of a hop spider when brewing. Mangrove Jack's Hop Spider (Grainfather)Diameter: 15 cm Length: 30 cm Material: 800 micron 304 grade stainless steel mesh, with stainless steel support band and single hook

Grainfather Magnetic Pump MP-10RN with C14 plug. Original. Standard 14mm input/output.

Whirlpooling and aerating is good practice before you pump the wort out of your brewing system. It infuses oxygen which promotes enhanced yeast activity and places the hops and protein back into suspension before the filtering process. The Grainfather Whirlpool and Aeration Brewing Paddle provides an excellent whirlpool by allowing the perfect amount of liquids and solids to pass through its large blades. Just simply attach to a standard electric power drill via its ‘chuck bit’ styled end for relaxed aeration of your wort. Grainfather Whirlpool and Aeration Paddle:- 304 stainless steel, 8mm (1/3”) drill bit end and 12.5 cm (5”) wide blades- Designed to be easily attached to a power drill via an 8mm (1/3”) drill bit style end- Plugged at the end- 56cm (22”) long, perfect for use in large boilers and smaller stove top kettles- 12.5cm (5”) wide blades to create a strong aeration and whirlpool

Use in conjunction with the Grainfather Connect Control Box thermometer, for accurate control of your wort transfer temperature through the Grainfather Counter Flow Chiller. Avoid long lag time and off flavours by using the Grainfather Wortometer. Adjust your wort and water flow rates from the Grainfather Counter Flow Chiller by dialling in the exact wort temperature your specific yeast requires. Requires a flexible 5-8 mm inner diameter silicon hose (not included). Instructions:https://www.grainfather.com/media/wysiwyg/V2_GF_WORTOMETER_INST_WEB.pdf

Hexagon Double Nipple NPT 1/2" to NPT 1/2". Stainless steel. Fits amonst other things Lauter-Helix 1000mm.

Much smoother and easier to keep clean than a net / hop bag. Used in the pot during brewing. Made from stainless steel with a diameter of 9.5 cm and includes a chain for easy submersion.

Hop Spider with fine stainless steel mesh to keep hops separated from the wort during the boil.InfoMaterial: 304 stainless steelMesh size: 300 micronsTotal length: 46cmLength of mesh basket: 35cmDiameter top: 15cmDiameter bottom: 10cm

Kegland "Little Red Spitfire" KL04329 CIP Spinning Spray Rotor is a low volume, inexpensive low-flow spray head for low voltage pumps as low as 6W up to 25W. The perfect spray head that has multiple uses over your brew day. 1/2" BSP thread. 300 mm length silicon. Stainless nut and barb. - Clean In Place (CIP) with your 35L, 65L or 100L BrewZilla (can be fitted to the other branded units) What can it do?- Clean In Place your 35L, 65L or 100L BrewZilla. Simply cut your recirculation hosing, or purchase additional silicone hosing to get the right length for your setup. You will be able to find the optimum length required by testing with water first. We found great success using the glass lid to start with to see if it is coating everything that you need it to. Specification 1 x Custom molded rotating spray head with 1/2" BSP thread1 x 300mm length silicon tubing suitable for your BrewZilla recirculation arm1 x Stainless nut and barb Please note: The rotating spray head can only be used in the downwards position, it cannot be tilted or mounted sideways or upside down.

The KegLand Sparge Sprinkler is a super simple device designed to help in spreading and distributing your wort in a mash tun / sparge vessel. It can also be used as the final transfer piece to assist in aerator your wort prior to pitching your yeast. It is also designed to fit through a BrewZilla Glass or Metal Distillation lid so you can recirculate evenly over your mash by adjusting the pumps ball valve or % Pump Feature for Gen 4 users.Specifications:1/2" Thread - 50mm Long - 20.4mm wide12.7mm Radial Seal Stainless Steel Barb-Tail with a 1/2" Stainless Steel Retaining Nut

Lauter-Helix 1000mm is a stainless steel , flexible spiral filter tube made to filter the vort from hops and debris between brewery/kettle and fermenter. Easy to clean by hnd or dish washer. Fitting: NPT 1/2".Can replace the bazooka filter in Coobra CB3 and CB5 together with a "Hexagon double nipple connector NPT 1/2" to NPT 1/2" which is sold seperately. May also fit other breweries.

Powerful and quiet 19L/min magnetic pump capable of handling water/wort up to 140°C. Perfect for recirculating wort or drinking water. Plastic Head.Do not run the pump dry.Specifications Magnetic Pump MP-15RMCapacity: max 19 L/min (60Hz)Head: max 3,4 meters (60Hz)Power rating: 10WConnections: 1/2" threaded males on both input and outputVoltage: 220-240V (50-60Hz)Protection: Class BPower cable: C13-plug (EU-version power cord (UK power cord NOT included))Note: Do not run the pump dry

Powerful and quiet 19L/min magnetic pump capable of handling water/wort up to 140°C. Perfect for recirculating wort or drinking water. Stainless Steel Head.Do not run the pump dry.Specifications Magnetic Pump MP-15RM Stainless Steel HeadCapacity: max 19 L/min (60Hz)Head: max 3,4 meters (60Hz)Power rating: 10WConnections: 1/2" BSP threaded males on both input and outputVoltage: 220-240V (50-60Hz)Protection: Class BPower cable: C13-plug (EU-version power cord (UK power cord NOT included))Note: Do not run the pump dry

Plastic Head for Magnetic Pump MP-15RM (spare part).

Stainless Steel Mash Paddle 61cm

The Brew Kit 25L is the perfect complement to your automatic brewery - we've put together the things you need to start brewing. Just add bottles and Recipe Kits (ingredients).Brew Kit 25L contains:- 25-liter (30L max) fermenter with med tap och lid- 25-liter (30L max) fermenter with lid (no tap)- Fermenter air lock- Bottle filler (fits the fermenter tap)- Automatic pump siphon 44cm (Note: without holder and clamp)- Bench Capper Better Brew- Mash Paddle 52cm- Thermometer- Bottle Washer Spin Mini- SanitizerNote: Does not contain bottles or ingredients.